Archive

Oct 28

Winterizing Your Swimming Pool

By adminNo Comments
3683250821 a582775576 m Winterizing Your Swimming Pool

1. If thru wall skimmer inlet and outlets are used, the skimmer must be blocked off with a block off plate to prevent any water from lying in the skimmer. The return fitting must also be blocked off by using a plug on the inside of the pool. It is very important that the return fitting not protrude into the pool and that water is not allowed to flow into the skimmer. If this is not followed, when the ice in your pool forms it will grab onto your skimmer and return fittings, and if the ice should shift it will rip your wall at these locations.
2. A properly sized ice compensator (pool pillow) must be secured in the pool water to relieve the ice pressure that can exert severe pressure on the pool wall.
3. The best way to install chemicals is before you do any winterizing processes. Super chlorinate the pool, run the filter for four to six hours, then install a winterizing kit and then put the cover on.
4. A cover must be used to keep out dirt and debris from the pool. It is important when securing the cover that enough slack is used so that it rests on the top of the water so that the pressure is not on the pool frame. A build up of snow on the top of the cover should be removed.

5. The filter should be thoroughly backwashed. If you have a cartridge or a diatomaceous earth filter, cartridge or elements should be removed sprayed down and cleaned. Next you should remove any winterizing plugs from the filter and from the pump. Next if you have a site glass on your valve that should be removed, the pressure gauge should be removed and shake out any water that might be inside. If you have an in-line Chlorinator removed the lid, remove the winterizing plug. Take out any chlorine and dispose of a properly. If you have a multi-port valve put the selector handle in between any two selections, this will hold the valve open and prevent any water laying in there that could freeze. Filter hoses should be removed and emptied. If you have a heater make sure the gas is turned off and the manifold winterizing plug is removed (don’t forget to remove any plugs in the heater. Failure to do so can cause very expensive damage).
Do not cover the pump with plastic this will cause moisture to build up which will seriously damage the inside of the pump. It is a good idea or to get a heater cover to keep any debris such as leaves, acorns, etc. this could start a fire when restarting a heater next year.
If you have any questions at all about any of these processes, please call 1800pools.com and asked for one of our experts to help you.
While the pool is winterized it is important that it remain undisturbed throughout the winter months.
This is Right!
The cover should lie on the surface of the pool water. Leave slack, do not pull tight. Any excessive accumulation of water, or snow should be removed immediately.
This is Wrong!
Do not install the cover this tight. The weight of snow or rain will force the cover at the seams and along the pool edges.
IMPORTANT: During the winter months, inspect your pool and surrounding area. Remove any accumulation of water, ice and snow from the top of the pool and from the skimmer and return to prevent formation of an ice, water or snow load which can cause severe damage to pool and pool cover.
It is essential that you monitor the amount of snow and ice on top of your pool during the winter months. If you feel that the cable that attaches the cover to the pool is too tight and is pulling up on the pool ledges, or is creating excessive weight on the pool, release the cable at once to prevent damage to the pool.
Please note: Improper installation of your pool cover can cause damage to your pool and will void all pool and cover warranties.
Mild Climates:
Your climate permits a longer swimming season. However, if there are many weeks in which your pool will not be used, continue routine maintenance on a reduced schedule instead of completely closing your pool for the season.
1. Begin by reducing filter-running time in half. Keep pH between 7.2-7.8 and free available chlorine between 1.0 and 3.0 parts per million (use tester). Follow pool equipment manufacturer’s instructions for proper care of equipment during this time.
2. If you do not cover your pool, clean your skimmer every week, maintain filter according to manufacturer’s instructions and vacuum as needed.
3. Covering your pool will keep out leaves and dirt. Before covering, shock treat according to manufacturer’s directions.
S.Merillat

Jun 24

Guide to Swimming Pool Filters

By adminNo Comments
137335979 2c8c401a95 m Guide to Swimming Pool Filters

One Equipment that every swimming pool must have is a pool filter. A swimming pool filter is the main process that keeps your swimming pool clean of the various debris that are brought in by wind, rain, cleaning supplies, toys, and swimmers. A pool filter works to keep the water clear and promotes safety and health while in the water. The pool filter has three main components that allow it to keep your water clear and safe for swimmers. First, there is a motor and pump that work to bring the water in and push it out during filtration. Then the filter itself falls into three categories DE (Diatomaceous Earth), cartridge and sand.

A DE (Diatomaceous Earth) filter is probably the best for filtering even the minutest particles that could be in the water. Diatomaceous Earth is a natural substance that is found in the soil. It has the consistency of a fine, white powder. A filter made of Diatomaceous Earth comes in two different types of filters, a spin filter and a vertical grid filter. These two terms simply signify how the filter is set up. The spin filter does not work as well as the vertical and is virtually obsolete today.
A sand filter makes use of sand to filter the water of particles and allows filtered water to run through easily. The cartridge filter works in the same manner as a Diatomaceous Earth filter but without the use of any substance other than fabric mesh to filter the water.
Here are a few things you should consider before purchasing a swimming pool filter:
First, find the volume of the entire swimming pool. To find the volume you must consider the shape of your pool:
If your pool is rectangular Multiply the following Length, width, average depth If your pool is circular Multiply the following Radius, 3.14, average depth
Next, figure the capacity of your pool. This will allow you to calculate how much water your swimming pool holds. This is an important factor in purchasing a pool filter. To find the capacity, multiply the volume (you found in step one) by 7.48.
You will then have to determine the type of filter you want. Consider if your pool would benefit from a cartridge, DE, or sand filter. You should also consider if you want the filter to be vacuum or pressure. It is suggested that you should make the filter slightly larger than your initial calculation to allow for better filtration.
It is important that you follow all recommended procedures outlined by the swimming pool manufacturer. This will help you in maintaining clear and healthy pool water that can be enjoyed by all swimmers.

May 20

Making A Great Swimming Pool

By adminNo Comments
2670736339 c5040d1dfd m Making A Great Swimming Pool

A swimming pool is one place where we all want to be on a hot day. Swimming is such a relaxing exercise, and it is enjoyed by people of all ages. Kids love splashing, while adults love swimming in the water. Swimming is an excellent sport, and reduces fat as well. A perfect swimming pool adds a lot of class to a beautiful home. If you are in the process of getting a pool or redoing your old pool, read on!

Swimming Pool Basics:

Typically, a swimming pool has the following major components:

Basin

Motor pump

Water filter

Chemical feeder

Drains

Returns

PVC plastic plumbing connecting all of these elements

A good pool will have all the following components, so that the water is moved continuously from the filter, cleaning it, sometimes through the heater also, so that regular temperature is maintained. The water is consistently cleaned using the chemical feeders, with the help of chlorine, as it keeps water free from any bacteria.

Doing up a great pool:

The drain system is best laid at the lower end of the pool with the surface slanting towards it, so that the water can flow easily through the drains. The drains should be covered with grates so that while swimming, people do not have their hair or swimsuits caught up in them. A strainer is attached at the mouth of drains so that any debris is caught. A good pool must have powerful pumps that can help water flow through the filter and chemical feeder; to and from the swimming pool.

High rate sand filters are the best kind of filters that will clean the water perfectly. They use sand to clean water of any debris present. Some pools may also use the diatomaceous earth filter, or a cartridge filter. This filter cleans very fine particles of debris. Ideally in any pool, the water should pass the filter every 30 minutes, and for the largest ones, every six hours.

The pump and filter should also be connected to a fresh water line. Calcium hypochlorite or sodium hypochlorite make great chemical cleaning agents. An automated chlorine feeder should be hooked to the filters for good chemical filtration.

Sodium carbonate and sodium bicarbonate should be used as per the requirement, to keep the pH under control right from 7.8 to 7.9. After filtration, the water should be sent back to the pool. A great pool requires the best of the filters, chemical filters, drains and pumps.

Most people look at the pool and think that that is the most important part of the set up, but in fact equally important is the pumps room, where pumps and filters are installed. A pump room is where the water quality is maintained. There are some other issues that one may face while getting a pool done. Some of these are:

When to dig a pool?

Contrary to popular thought, winter, not spring or summer is the right time to get a pool dug up, as the ground is not soggy. Soft ground is difficult to dig and is not easy on heavy equipment as well.

Sides caving in:

The sides of the hollow dug must be sloping so that the sides do not cave in. The ideal ratio should be a 1-foot vertical drop for every 3 horizontal feet. Steel enforcements may also be used to keep the pool in shape.

Algae in the pool:

Algae can be very harmful to a swimming pool, and requires chemical treatment and a lot of filtering, backwashing, scrubbing, and skimming. Whatever kind of algae it is, quick treatment is essential, as algae is quick to take over the pool.

Kids safety:

Kids are sometimes unpredictable, so a cover on the pool or a fence around it will help to keep the pool area safe.

Winter:

If the swimming pool is outdoors and the winters are harsh, it is a good idea to put antifreeze in the key areas after draining the water and putting a cover over the pool.

A swimming pool is an ideal feature for your home; just remember a good pool requires extensive preparations, and once these are done, maintenance is very important.

Sep 25

Basic Guide To Swimming Pool Filters

By adminNo Comments
137361752 6604952a3f m Basic Guide To Swimming Pool Filters

One item that every swimming pool must have is a pool filter. A swimming pool filter is the main process that keeps your swimming pool clean of the various debris that are brought in by wind, rain, cleaning supplies, toys, and swimmers. A pool filter works to keep the water clear and promotes safety and health while in the water. The pool filter has three main components that allow it to keep your water clear and safe for swimmers. First, there is a motor and pump that work to bring the water in and push it out during filtration. Then the filter itself falls into three categories DE (Diatomaceous Earth), cartridge and sand.

A DE (Diatomaceous Earth) filter is probably the best for filtering even the minutest particles that could be in the water. Diatomaceous Earth is a natural substance that is found in the soil. It has the consistency of a fine, white powder. A filter made of Diatomaceous Earth comes in two different types of filters, a spin filter and a vertical grid filter. These two terms simply signify how the filter is set up. The spin filter does not work as well as the vertical and is virtually obsolete today.

A sand filter makes use of sand to filter the water of particles and allows filtered water to run through easily. The cartridge filter works in the same manner as a Diatomaceous Earth filter but without the use of any substance other than fabric mesh to filter the water.

Here are a few things you should consider before purchasing a swimming pool filter:

First, find the volume of the entire swimming pool. To find the volume you must consider the shape of your pool:

If your pool is rectangular Multiply the following Length, width, average depth

If your pool is circular Multiply the following Radius, 3.14, average depth

Next, figure the capacity of your pool. This will allow you to calculate how much water your swimming pool holds. This is an important factor in purchasing a pool filter. To find the capacity, multiply the volume (you found in step one) by 7.48.

You will then have to determine the type of filter you want. Consider if your pool would benefit from a cartridge, DE, or sand filter. You should also consider if you want the filter to be vacuum or pressure. It is suggested that you should make the filter slightly larger than your initial calculation to allow for better filtration.

There are a lot of different aspects that must be taken into consideration when purchasing a swimming pool filter. For the entire filtration system you can expect to pay anywhere from $20.00(USD) to $300.00 (USD). Replacement filters are slightly cheaper in some aspects, depending on the type of filter your system uses, you can expect to pay anywhere from $4.00 (USD) to $200.00 (USD).

It is important that you follow all recommended procedures outlined by the swimming pool manufacturer. This will help you in maintaining clear and healthy pool water that can be enjoyed by all swimmers.

Mar 29

Guide to Swimming Pool Filters

By adminNo Comments
3888825314 9d11ff6444 m Guide to Swimming Pool Filters

One Equipment that every swimming pool must have is a pool filter. A swimming pool filter is the main process that keeps your swimming pool clean of the various debris that are brought in by wind, rain, cleaning supplies, toys, and swimmers. A pool filter works to keep the water clear and promotes safety and health while in the water. The pool filter has three main components that allow it to keep your water clear and safe for swimmers. First, there is a motor and pump that work to bring the water in and push it out during filtration. Then the filter itself falls into three categories DE (Diatomaceous Earth), cartridge and sand.

A DE (Diatomaceous Earth) filter is probably the best for filtering even the minutest particles that could be in the water. Diatomaceous Earth is a natural substance that is found in the soil. It has the consistency of a fine, white powder. A filter made of Diatomaceous Earth comes in two different types of filters, a spin filter and a vertical grid filter. These two terms simply signify how the filter is set up. The spin filter does not work as well as the vertical and is virtually obsolete today.
A sand filter makes use of sand to filter the water of particles and allows filtered water to run through easily. The cartridge filter works in the same manner as a Diatomaceous Earth filter but without the use of any substance other than fabric mesh to filter the water.
Here are a few things you should consider before purchasing a swimming pool filter:
First, find the volume of the entire swimming pool. To find the volume you must consider the shape of your pool:
If your pool is rectangular Multiply the following Length, width, average depth If your pool is circular Multiply the following Radius, 3.14, average depth
Next, figure the capacity of your pool. This will allow you to calculate how much water your swimming pool holds. This is an important factor in purchasing a pool filter. To find the capacity, multiply the volume (you found in step one) by 7.48.
You will then have to determine the type of filter you want. Consider if your pool would benefit from a cartridge, DE, or sand filter. You should also consider if you want the filter to be vacuum or pressure. It is suggested that you should make the filter slightly larger than your initial calculation to allow for better filtration.
It is important that you follow all recommended procedures outlined by the swimming pool manufacturer. This will help you in maintaining clear and healthy pool water that can be enjoyed by all swimmers.

< Older
Blue Taste Theme created by Jabox